Benchmark Control Problem for Highway Bridge based on FLC

Fuzzy logic control (FLC) systems have been applied as an effective control system in various fields, including vibration control of structures. The advantage of this approach is its inherent robustness and ability to handle non‐linearities and uncertainties in structural behavior and loading. The study evaluates the three‐dimensional benchmark control problem for a seismically excited highway bridge using an ANFIS driven hydraulic actuators. An ANN based training strategy that considers both velocity and acceleration feedback together with a fuzzy logic rule base is developed. Present study needs only 4 accelerometers and 4 fuzzy rule bases to determine the control force, instead of 8 accelerometers and 4 displacement transducers used in the benchmark study problem. The results obtained are better than that obtained from the benchmark control algorithm.

Analysis of a concrete arch highway bridge reinforced with structural steel

An article in the Engineering News-Record for March 30, 1923, describes a new concrete arch bridge across the Connecticut River between Springfield and West Springfield, Mass.

Design of a timber Howe truss highway bridge

The span of the bridge was assumed as 100 feet. The type of bridge used is the timber Howe Truss. The height of truss was taken as 20 feet between center lines of top and bottom chords. The width was taken as 18 feet center to center of trusses. The truss was divided up into five panels 20 feet long.

It was designed according to the "General Specifications for Steel Highway Bridges" by Ketchum. For the live load for the floor and its supports, a load of 80 pounds per square foot of total floor surface or a 15 ton traction engine with axles 10 feet centers and 6 feet gage, two thirds of load to be carried by rear axles.

For the truss a load of 75 pounds per square foot of floor surface.

For the wind load the bottom lateral bracing is to be designed to resist a lateral wind load of 300 pounds per foot of span; 150 pounds of this to be treated as a moving load.

The top lateral bracing is to be designed to resist a lateral wind force of 150 pounds per foot of span.

The timber to be used in the bridge is to be Douglas fir.

The unit stresses used for timber are those of the American Railway Engineering Association.

Seismic design of highway bridge foundations.

"June 1986."

Report on a proposed highway bridge across the Columbia River at Astoria, Oregon, for the Port of Astoria, Oregon, Pacific County, Washington Oregon State Highway Commission [and] Washington Toll Bridge Authority, March 1955

Plans and cost estimates, by Tudor Engineering Company.--Traffic and revenue estimates, by Coverdale & Colpitts.

Report upon a traffic investigation for a proposed highway bridge between Easton and Phillipsburg, located at the foot of Bushkill street, Easton, Pennsylvania, to the Delaware river joint toll bridge commission, Pennsylvania-New Jersey, October 1935.

Mimeographed.

Optimal dynamic inversion-based semi-active control of benchmark bridge using MR dampers

A new two-stage state feedback control design approach has been developed to monitor the voltage supplied to magnetorheological (MR) dampers for semi-active vibration control of the benchmark highway bridge. The first stage contains a primary controller, which provides the force required to obtain a desired closed-loop response of the system. In the second stage, an optimal dynamic inversion (ODI) approach has been developed to obtain the amount of voltage to be supplied to each of the MR dampers such that it provides the required force prescribed by the primary controller. ODI is formulated by optimization with dynamic inversion, such that an optimal voltage is supplied to each damper in a set. The proposed control design has been simulated for both phase-I and phase-II study of the recently developed benchmark highway bridge problem. The efficiency of the proposed controller is analyzed in terms of the performance indices defined in the benchmark problem definition. Simulation results demonstrate that the proposed approach generally reduces peak response quantities over those obtained from the sample semi-active controller, although some response quantities have been seen to be increasing. Overall, the proposed control approach is quite competitive as compared with the sample semi-active control approach.

Structural health monitoring in Australia

Structural Health Monitoring (SHM) is defined as the use of on-structure sensing system to monitor the performance of the structure and evaluate its health state. Recent bridge failures, such as the collapses of the 1-35W Highway Bridge in USA, the collapse of the Can Tho Bridge in Vietnam and the Xijiang River Bridge in the Mainland China, all of which happened in the year 2007, have alerted the importance of structural health monitoring. This book presents a background of SHM technologies together with its latest development and successful applications. It is a book launched to celebrate the establishment of the Australian Network of Structural Health Monitoring (ANSHM). The network comprising leading SHM experts in Australia promotes and advances SHM research, application, education and development in Australia.

Verificação à fadiga de pontes rodoviárias mistas (aço-concreto)

As pontes rodoviárias mistas (aço-concreto) estão sujeitadas às ações dinâmicas variáveis, por exemplo, devido ao tráfego de veículos sobre a superfície irregular do pavimento. Estas ações dinâmicas podem gerar a nucleação de fraturas ou mesmo a sua propagação sobre a estrutura. A correta consideração desses aspectos objetivou o desenvolvimento de uma metodologia de análise, com a finalidade de avaliar os níveis dos esforços e tensões oriundos do tráfego dos veículos sobre a superfície irregular do pavimento e, bem como, proceder uma verificação à fadiga de obras de arte rodoviárias em aço e mistas (aço-concreto). Para tal, as técnicas para a contagem de ciclos de tensão e a aplicação das regras de dano acumulado foram analisadas através de curvas do tipo S-N, associadas a diversas normas de projeto. A ponte rodoviária mista (aço-concreto) investigada neste estudo é constituída por quatro vigas de aço longitudinais e por um tabuleiro de concreto armado. O modelo numérico-computacional, desenvolvido para a análise dinâmica da ponte, foi concebido com base em técnicas usuais de discretização através do método dos elementos finitos. Simulam-se as almas das vigas de aço e as lajes de concreto do tabuleiro através de elementos finitos de casca. As mesas dessas vigas, transversinas e os enrijecedores são modelados por elementos de viga tridimensionais. Os veículos são representados a partir de sistemas "massa-mola-amortecedor". O tráfego dessas viaturas é considerado mediante a simulação de comboios semi-infinitos, deslocando-se com velocidade constante sobre a ponte. As conclusões da presente investigação versam acerca da vida útil de serviço dos elementos estruturais de pontes mistas (aço-concreto).

Influência da Velocidade, do Espaçamento e do Número de Veículos sobre a Resposta Dinâmica de Pontes Rodoviárias de Concreto Armado.

Nesta dissertação são avaliados os efeitos dinâmicos provenientes da travessia de comboios de veículos sobre o tabuleiro irregular de obras de arte rodoviárias de concreto armado. O modelo matemático empregado para simular o comportamento do sistema veículo-ponte considera a participação da massa e da rigidez das viaturas na definição das freqüências do sistema e, conseqüentemente, a força de interação entre os veículos e a ponte é afetada pela flexibilidade desta. A ponte é modelada a partir do emprego de elementos finitos de barra unidimensionais e discretizado com massas concentradas e flexibilidade distribuída. O modelo de veículo empregado baseia-se no veículo TB-12 preconizado pela norma brasileira NBR 7188. Este veículo é simulado por sistemas de massas, molas e amortecedores sendo descrito por graus de liberdade à translação e rotação no plano. As irregularidades da pista são definidas por um modelo não-determinístico com base na densidade espectral do pavimento. O carregamento sobre a ponte é constituído por sucessões de veículos deslocando-se com velocidade constante sobre a obra. Devido à própria natureza das irregularidades da pista e do comboio de veículos, atenção especial é concentrada na fase permanente da resposta do sistema. São estudadas as respostas de dois modelos estruturais existentes, com base em tabuleiros isostáticos, em concreto armado, com e sem balanços, em seção do tipo T e duplo T, respectivamente, em termos de deslocamentos e esforços nas seções onde ocorrem os efeitos máximos. As conclusões do trabalho versam sobre a influência da velocidade, espaçamento e do número de veículos, referentes a situações distintas de carregamento, no que tange a resposta dinâmica das pontes rodoviárias de concreto armado. A magnitude dos efeitos dinâmicos associados à interação dos veículos com o pavimento irregular também é investigada.

Projecto de execução de uma obra de arte

Trabalho de Projecto para obtenção do grau de Mestre em Engenharia na Área de Especialização em Estruturas

Sistemas e soluções pós-tensão na reabilitação de obras de arte

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil

Simplified design method for energy dissipating devices in retrofitting of seismically isolated bridges

Abstract: Highway bridges have great values in a country because in case of any natural disaster they may serve as lines to save people’s lives. Being vulnerable under significant seismic loads, different methods can be considered to design resistant highway bridges and rehabilitate the existing ones. In this study, base isolation has been considered as one efficient method in this regards which in some cases reduces significantly the seismic load effects on the structure. By reducing the ductility demand on the structure without a notable increase of strength, the structure is designed to remain elastic under seismic loads. The problem associated with the isolated bridges, especially with elastomeric bearings, can be their excessive displacements under service and seismic loads. This can defy the purpose of using elastomeric bearings for small to medium span typical bridges where expansion joints and clearances may result in significant increase of initial and maintenance cost. Thus, supplementing the structure with dampers with some stiffness can serve as a solution which in turn, however, may increase the structure base shear. The main objective of this thesis is to provide a simplified method for the evaluation of optimal parameters for dampers in isolated bridges. Firstly, performing a parametric study, some directions are given for the use of simple isolation devices such as elastomeric bearings to rehabilitate existing bridges with high importance. Parameters like geometry of the bridge, code provisions and the type of soil on which the structure is constructed have been introduced to a typical two span bridge. It is concluded that the stiffness of the substructure, soil type and special provisions in the code can determine the employment of base isolation for retrofitting of bridges. Secondly, based on the elastic response coefficient of isolated bridges, a simplified design method of dampers for seismically isolated regular highway bridges has been presented in this study. By setting objectives for reduction of displacement and base shear variation, the required stiffness and damping of a hysteretic damper can be determined. By modelling a typical two span bridge, numerical analyses have followed to verify the effectiveness of the method. The method has been used to identify equivalent linear parameters and subsequently, nonlinear parameters of hysteretic damper for various designated scenarios of displacement and base shear requirements. Comparison of the results of the nonlinear numerical model without damper and with damper has shown that the method is sufficiently accurate. Finally, an innovative and simple hysteretic steel damper was designed. Five specimens were fabricated from two steel grades and were tested accompanying a real scale elastomeric isolator in the structural laboratory of the Université de Sherbrooke. The test procedure was to characterize the specimens by cyclic displacement controlled tests and subsequently to test them by real-time dynamic substructuring (RTDS) method. The test results were then used to establish a numerical model of the system which went through nonlinear time history analyses under several earthquakes. The outcome of the experimental and numerical showed an acceptable conformity with the simplified method.

Performance en fluage des assemblages antiglissement avec des surfaces métallisées dans les ponts en acier

Les éléments des ponts en acier sont exposés à de sévères conditions environnementales, tel l’épandage de sels déglaçant sur les routes. Ces éléments ont besoin d’un niveau suffisant de protection contre la corrosion afin de préserver leur intégrité à long terme. Une solution efficace, devenue populaire au Canada, est la métallisation. La métallisation est un revêtement anticorrosion formé par projection thermique de métal, généralement du zinc, sur la surface à protéger. La protection fournie au substrat d’acier est assurée par une barrière physique et une protection galvanique. Pour le calcul des assemblages boulonnés antiglissement, les codes de conception, tel le code Canadien sur le calcul des ponts routiers CAN/CSA S6-14, spécifient, en fonction des conditions des surfaces de contact désirées, un coefficient de glissement à utiliser. Actuellement, ces codes ne fournissent aucun coefficient de glissement entre deux surfaces métallisées. Donc, il est pratique courante pour les fabricants de ponts en acier de masquer les surfaces de contact des joints boulonnés avant de métalliser, ce qui est très couteux pour l’industrie puisque ce travail doit se faire manuellement. Récemment, des études ont évalué la résistance au glissement à court terme d’assemblages antiglissement ayant des surfaces de contact métallisées. Les résultats ont révélé une résistance au glissement supérieure aux assemblages sur acier nu grenaillés. Dans la présente recherche, la performance en fluage des assemblages antiglissement métallisés a été caractérisée pour s’assurer qu’une résistance en glissement de Classe B soit toujours valide à long terme. L’effet de la relaxation de la force de serrage sur la charge de glissement a aussi été évalué. Les résultats ont démontré une bonne performance en fluage. Aussi, les résultats ont révélé que la relaxation de la force de serrage n’a pas d’impact significatif sur la résistance au glissement des assemblages antiglissement métallisés. Les conclusions de cette étude pourraient bien influencer de futures révisions des codes de conception et avoir un impact sur l’industrie de l’acier en Amérique du Nord.Mots clés : Assemblage boulonné antiglissement, métallisation, pont routier en acier, fluage, relaxation

An investigation of the effectiveness of existing bridge design methodology in providing adequate structural resistance to seismic disturbances : Phase III, Nonlinear soil-structure interaction of skew highway bridges : final report : prepared for Federal Highway Administration, Offices of Research and Development /

Bibliography: p. 46-48.